Yes, it should look like this. You can find more explanation here - interesting reading:
http://www.laserfx.com/Backstage.LaserF ... ning1.html
http://www.pangolin.com/ILDAtest.html
I am afraid that I am not that good in programming to be able to look for possible source of issues in your code. Anyway, is the source located somewhere in your github repository?
Btw, are you still considering development of Pro version?
LaserShark what i have got working.
-
- Posts: 41
- Joined: Tue Jul 08, 2014 7:39 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LaserShark what i have got working.
PacManFan, I just checked Lasershark behavior with different galvo + driver set. Unfortunately without any change, the distortion and noises are still present...
-
- Posts: 20
- Joined: Tue Jun 17, 2014 10:27 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LaserShark what i have got working.
PacManFan where do you have released the source of the lasershark plugin?
-
- Posts: 13
- Joined: Tue Oct 07, 2014 9:01 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LaserShark what i have got working.
i just started testing a lasershark galvo setup and i'm encountering the following problems.
-blanking of the even and uneven scanlines is not in sync, meaning that the edges are jagged
-black vertical lines(also jagged), those lines do not appear in the slice preview
attached are 2 pictures of a sliced cube that illustrate the problem.
the problem occurs on the following configurations:
winxp sp3 32bit
win7 sp1 64bit
win7 sp1 64bit running in a virtual machine on osx
win7 sp1 32bit running in a virtual machine on osx
-blanking of the even and uneven scanlines is not in sync, meaning that the edges are jagged
-black vertical lines(also jagged), those lines do not appear in the slice preview
attached are 2 pictures of a sliced cube that illustrate the problem.
the problem occurs on the following configurations:
winxp sp3 32bit
win7 sp1 64bit
win7 sp1 64bit running in a virtual machine on osx
win7 sp1 32bit running in a virtual machine on osx
-
- Posts: 13
- Joined: Tue Oct 07, 2014 9:01 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LaserShark what i have got working.
update:
i recompiled the plugin with the zigzag disabled and the jagged lines are gone.
the jagged line are probably introduced by hardware latencies in the galvo system and/or latencies in the on-off switching of the laser.
the vertical lines are introduced by the lasershark firmware.
apparently the laser is intentionally switched off after all the buffer samples are used up.
i recompiled the plugin with the zigzag disabled and the jagged lines are gone.
the jagged line are probably introduced by hardware latencies in the galvo system and/or latencies in the on-off switching of the laser.
the vertical lines are introduced by the lasershark firmware.
apparently the laser is intentionally switched off after all the buffer samples are used up.
- PacManFan
- Site Admin
- Posts: 633
- Joined: Sun Dec 01, 2013 11:44 am
- Location: Ahead of the curve [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LaserShark what i have got working.
If this is a case of 'sample under-run', then you might be able to increase the sample rate through the config file. This will help keep the lasershark buffer full.
-Steve
-Steve
-
- Posts: 41
- Joined: Tue Jul 08, 2014 7:39 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LaserShark what i have got working.
I got 2pcs of Lasershark for sale in EU(Slovakia). Anybody interested?