My printer with resin and LCD screen.
Raspberry PI 3 - nanoDlp - Movement GPIOs - Drivers a4988
LCD 5 inch 800x480 not BEF
x/y 0.135mm
Layer Thickness = 0.05mm
Cure Time = 10 seconds
Lift 2mm
Daylight Resins
matrix LED 11W
These are my results:
I have a lot of work.
LCD SLA 3D Printer
-
- Posts: 9
- Joined: Tue Sep 06, 2016 7:39 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
-
- Posts: 301
- Joined: Tue Dec 24, 2013 10:25 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LCD SLA 3D Printer
hi ionel.ciobanuc,
Welcome to the forum, I've been watching your lcd printer, very impressive and great work..
allot of work!
cheers,
hp
Welcome to the forum, I've been watching your lcd printer, very impressive and great work..
allot of work!
cheers,
hp
-
- Posts: 81
- Joined: Fri Oct 17, 2014 1:06 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LCD SLA 3D Printer
The first test after the rebuild of my LCD 3D printer
-
- Posts: 81
- Joined: Fri Oct 17, 2014 1:06 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LCD SLA 3D Printer
I sold the rights to the membrane of another company
For the printer I use 1280x800 7 inches LCD and four kinds of LEDs with different power and different wavelength. I'm still not sure if this is the right combination because there are a problems if I use 100% power. The resin is cured the entire of the bottom.
Regards
For the printer I use 1280x800 7 inches LCD and four kinds of LEDs with different power and different wavelength. I'm still not sure if this is the right combination because there are a problems if I use 100% power. The resin is cured the entire of the bottom.
Regards
-
- Posts: 9
- Joined: Tue Sep 06, 2016 7:39 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LCD SLA 3D Printer
My VAT
Matrix LED is in testing. I have trouble angle.
I used:
I'm working on one with
How connected "display iPad4" to raspberry?
Matrix LED is in testing. I have trouble angle.
I used:
I'm working on one with
How connected "display iPad4" to raspberry?
-
- Posts: 2
- Joined: Wed Mar 18, 2015 9:39 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LCD SLA 3D Printer
Nice work ! and nice results !
Could you please tell from where did you bought the film ?
(I am also from Ro)
Kind regards,
Daniel
Could you please tell from where did you bought the film ?
(I am also from Ro)
Kind regards,
Daniel
-
- Posts: 9
- Joined: Tue Sep 06, 2016 7:39 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: LCD SLA 3D Printer
It did not work with the original background light. Or I did not have patience.