Uploaded this to DB for anyone that is wanting to use Marlin on there DLP build with CW. It is setup to use a hobby servo off of pin D11
You will need to change the max travel limits after homing to fit your build, this uses one end stop for the Z and software limited for the height.
End stops will also have to be configured depending on which type your using, this build is setup for hall effect end stops.
Clinton
Working Marlin Firmware
-
- Posts: 11
- Joined: Mon Sep 29, 2014 8:55 pm
- Location: Pretoria South Africa [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
Hi i also tri to load my new dlp projector software what i have built in same concept. I tri to download your file for marlin but forum says it has been removed. Please help
-
- Posts: 50
- Joined: Mon Nov 10, 2014 1:26 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
I have the same problem, must set up firmaware Marlin for the CW.
I can not find where seting the pins step and direction in firmaware.
If anyone can help thanks.
I can not find where seting the pins step and direction in firmaware.
If anyone can help thanks.
- cncbasher
- Posts: 54
- Joined: Sun Nov 02, 2014 10:09 am
- Location: uk [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
all settings are in configuration.h
this also depends on what breakout board your using such as ramps or sanguino etc
this also depends on what breakout board your using such as ramps or sanguino etc
-
- Posts: 2
- Joined: Mon Feb 23, 2015 2:51 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
anyone can help me to have malin firmware so that I can use it for my dlp type printer.
I have z axis and ramps 1.4 and arduino mega 2650. tilting only z axis.
I want to have servo shutter for the printer.
i have try to look for the drop box and it say gone...
I have z axis and ramps 1.4 and arduino mega 2650. tilting only z axis.
I want to have servo shutter for the printer.
i have try to look for the drop box and it say gone...
-
- Posts: 22
- Joined: Sun Mar 08, 2015 4:25 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
Or if anyone else could upload configured Merlin/Sprinter firmware which works with CW? Thank you in advance.
-
- Posts: 159
- Joined: Thu Jan 01, 2015 2:56 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
uploaded mine. is working with 5 mm pitch screw, 1/16 microstepping, 1.8º stepper, endstops activated, servo activated, 200 mm z travel, ramps 1.4 and lcd activated also.
good luck !
i dont take responsability if your house burns or falls apart
good luck !
i dont take responsability if your house burns or falls apart
-
- Posts: 22
- Joined: Sun Mar 08, 2015 4:25 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
Thank a lot
-
- Posts: 3
- Joined: Wed Sep 09, 2015 4:47 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Working Marlin Firmware
can anyone post the configuration file of a working marlin firmware for DLP 3D printer. i m struggling a lot. unable to do changes. help me.