Search found 12 matches

by carlosx01
Wed May 10, 2017 5:07 pm
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

Hi my printer use 2 pieces 10 wat led chips and for resin funtodoo i use for 30microns layer time 7,5 sek... i was replace screew and control board with original arduino with ramps and install nano dlp (slicing in creation workshop is very very slow) now I am printing ok but it need little better se...
by carlosx01
Mon May 08, 2017 3:00 pm
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

Hi all have somebody installed 50 or more wats led chip? and how it works? lifetime of display, additional cooling, and precision of prints with single and multiple chips... time per layer before modification and after and some photos? i need use wax resins but this printer have low power for cure t...
by carlosx01
Sun Apr 30, 2017 6:54 am
Forum: Resins
Topic: Makerjuice Waxcast stock.
Replies: 5
Views: 13628

Re: Makerjuice Waxcast stock.

Hi guys have somebody experience with direct casting of gold. And results? How many ash have this resin? And burnout temperature? I use funtodoo castable and senertec castable resin and after burning 5 hours on 850 grade of celsius it have many ash and when you are not use vacuum cleaner before cast...
by carlosx01
Fri Apr 14, 2017 11:54 am
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

Hi Creation Workshop does not see the printer. I have an updated version with Pi3 Resin sticks to the platform and Teflon From the LogBindle file in the printer. Not the correct settings in my opinion Hi I am printing from photonic 3D is included on raspberry memory card. Creation workshop i use on...
by carlosx01
Tue Apr 11, 2017 4:55 pm
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

Hi guys all the problems are solved. Printer works well. Prints are perfect. Two weeks of troubles and now is all working good (change two cables many times reinstal software and lot of unsuccessful prints) maybe faulty piece of this printer... for funtodoo cast I use for first 2layers time 60seknds...
by carlosx01
Sat Apr 08, 2017 3:46 am
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

Hi all. I was replace HDMI cable with new one and problem with display is fixed I hope. I test print but I make something wrong. I use resin from senetrek from Turkey and funtodo resin from China and result is the same. For first 3 layers 120000 ms thicknes 0,025mm and for normal layer time from 10 ...
by carlosx01
Thu Apr 06, 2017 5:10 pm
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

It is not glue in connector. When the diplay failed function I must connector (HDMI) take out of raspberry and then back and sometimes is it good sometimes not... it can be display board... now after many ours of testing I can say display failing not depend from temperature I think that can be displ...
by carlosx01
Wed Apr 05, 2017 5:02 pm
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

Now 2 times (every test 1,5 hour) dry test without resin tank normal display function no problem when i use resin tank with resin the function is failed... I think that the display is overheated.. cooling is none... tomorrow I test measure temperature on the display and next i apply upgrade.. moving...
by carlosx01
Wed Apr 05, 2017 2:20 am
Forum: Hardware
Topic: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,
Replies: 437
Views: 1407389

Re: 5.5 inch (2560x1440p LCD) with UV LED array for under $600. :Proniks Sla 3d Printer,

Hi guys I have this same problem with this printer. Display dont work correct.. Sometimes when I make dry test without resin tank it works but when I use resin tank with resin and start the printing display failed... when I move with HDMI cable It is little better but not for long time...(5 or 10 mi...