Hi again
I'm using the Acer P1500 with my LittleRP and was wondering if others that uses the same projector have played with specific settings in the menu for the projector to get better results, besides focusing on the lens and maybe moving the projector a hole or two backwards?
Acer P1500 settings?
-
- Posts: 6
- Joined: Sun Apr 26, 2015 5:26 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Acer P1500 settings?
Kochen, Denmark, Europe
-
- Posts: 236
- Joined: Sat Mar 29, 2014 6:16 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
Users have reported better image projecting by moving to a further back position, I included the acyrilc spacers so you could play with the positioning, generally for every hole you go back you lose 1 acrylic spacer so the projector sits lower, this should keep the image projection centered.
-
- Posts: 8
- Joined: Fri Apr 10, 2015 10:06 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
I've got mine of the furthest front. (It's an early m3 not m4 model mount)
I've basically got it on default projector settings. I have noticed that is uneven. Center/right is best left has problems with being underexposed. Not sure if there is anything that can be done. If i crank it up so the left is exposed properly, the right gets overexposed.
I've basically got it on default projector settings. I have noticed that is uneven. Center/right is best left has problems with being underexposed. Not sure if there is anything that can be done. If i crank it up so the left is exposed properly, the right gets overexposed.
-
- Posts: 6
- Joined: Sun Apr 26, 2015 5:26 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
Thanks for your inputs so far.. I hope that I can get the time to play around with settings and so in the next few days..
Kochen, Denmark, Europe
-
- Posts: 10
- Joined: Wed Jun 24, 2015 7:52 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
Kochen,
Were you able to play with the projector settings at all? I have been messing with mine a little bit and am having a hard time finding a good consistent setting. I'm either under or overexposing. I'm using the H6510BD printer and madesolid V2 Red resin. I tried a few of the brighter modes, but got overexposure and bleeding in the center. Just trying to find a good starting point again.
Were you able to play with the projector settings at all? I have been messing with mine a little bit and am having a hard time finding a good consistent setting. I'm either under or overexposing. I'm using the H6510BD printer and madesolid V2 Red resin. I tried a few of the brighter modes, but got overexposure and bleeding in the center. Just trying to find a good starting point again.
-
- Posts: 25
- Joined: Fri Jun 19, 2015 5:12 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
Same issue here - left third of the build plate is underexpoed compared to the centre and right. Makerjuice SF. I'm using a 6510 (P1500 with another name).
Perhaps applying a mask in Creation workshop to the "good" area, and upping the exposure overall would even it out (at the cost of print time)
Perhaps applying a mask in Creation workshop to the "good" area, and upping the exposure overall would even it out (at the cost of print time)
-
- Posts: 49
- Joined: Mon Aug 03, 2015 10:14 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
Me too not happy with uneven exposure. At the front part of build volume it is too weak. This model had broken because of it:
But how to make good exposure mask? I saw some kind of light sensor on Envisiontec 3d printers, it was used during calibration. Maybe, we need some hardware too, for this purpose.
But how to make good exposure mask? I saw some kind of light sensor on Envisiontec 3d printers, it was used during calibration. Maybe, we need some hardware too, for this purpose.
Last edited by DanOrgan on Thu Aug 06, 2015 3:03 am, edited 1 time in total.
-
- Posts: 236
- Joined: Sat Mar 29, 2014 6:16 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
I am working on a method to 'map' out the uv intensity variance of these projectors to generate a mask for each model.
-
- Posts: 49
- Joined: Mon Aug 03, 2015 10:14 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Acer P1500 settings?
Hi, Goopyplastic. How are you going to measure UV intensity?
I purchased cheap $10 Arduino-compatible UV-sensor from (sorry, Russian site). Maybe it will be useful.
I purchased cheap $10 Arduino-compatible UV-sensor from (sorry, Russian site). Maybe it will be useful.