Some good info hp. Thanks.
Spent some time browsing panelook and found that the all the higher res screens don't have as high of brightness as a lower res screens. It seems the the guys at photocentric3d.com went with that low res screen for a reason. You just can't find a retina type screen with a really high brightness.
This is leading me to the conclusion we'd need an LED array after all. Kinda of a pain but I'm betting we could get really short cure times.
Shipping of the Daylight resin to US is a bit much, contacted them and they said they'll have a US distributor in a few months. I might try the bucktownpolymer visible light resin in the mean time.
Daylight Polymer 3D Printer
-
- Posts: 30
- Joined: Tue Feb 04, 2014 9:57 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Daylight Polymer 3D Printer
LED aluminium PCB and LED Driver arrived today.
my second iPad Retina Display with Abusemark adapter attached ,ready to be stripped down ...
460-470nm 1W LED and lenses / diffuser should be bought tomorrow.
Regarding the resin , I unfortunately have no choice , 60GBP only for shipping to Hongkong , they cannot ship to China mainland directly ...
Keep you updated .
my second iPad Retina Display with Abusemark adapter attached ,ready to be stripped down ...
460-470nm 1W LED and lenses / diffuser should be bought tomorrow.
Regarding the resin , I unfortunately have no choice , 60GBP only for shipping to Hongkong , they cannot ship to China mainland directly ...
Keep you updated .
-
- Posts: 30
- Joined: Tue Feb 04, 2014 9:57 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
-
- Posts: 301
- Joined: Tue Dec 24, 2013 10:25 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Daylight Polymer 3D Printer
hi oliveenchine,
check it out I found an adapter..
https://www.allekabels.nl/searchresult. ... rd=1369642
HDMI to displayport 1.2 supprting 4K resolution
cost is 44 Euro
cheers,
hp
check it out I found an adapter..
https://www.allekabels.nl/searchresult. ... rd=1369642
HDMI to displayport 1.2 supprting 4K resolution
cost is 44 Euro
cheers,
hp
-
- Posts: 189
- Joined: Mon Dec 09, 2013 4:28 pm
- Location: Houston, TX
- Contact:
Re: Daylight Polymer 3D Printer
@AndersonHTa
-
- Posts: 43
- Joined: Wed Aug 13, 2014 6:44 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Daylight Polymer 3D Printer
Is there a spec sheet for the Daylight resin and what wavelength it cures at best? There seems to be two typical options of LEDs:
Royal Blue (440 - 450 nm)
Bright Blue (460 - 470 nm)
Would Royal Blue be better because it's closer to UV?
Royal Blue (440 - 450 nm)
Bright Blue (460 - 470 nm)
Would Royal Blue be better because it's closer to UV?
-
- Posts: 30
- Joined: Tue Feb 04, 2014 9:57 am [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable