Daylight Polymer 3D Printer

Post, review and discuss any commercial machines. Try to include links, specifications and prices.
hp_
Posts: 301
Joined: Tue Dec 24, 2013 10:25 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby hp_ » Fri Feb 26, 2016 11:49 am

it looks like photocentric3d change the spec for the 10" printer

SPEED AT 100mic. 20 sec/layer +8 sec mechanical

i can remember that i saw different Speeds there :)

cheers,

hp

AndersonTa
Posts: 189
Joined: Mon Dec 09, 2013 4:28 pm
Location: Houston, TX
Contact:

Re: Daylight Polymer 3D Printer

Postby AndersonTa » Mon Feb 29, 2016 11:45 pm

Anyone got any updates with there attempts with Daylight resins?
@AndersonHTa

nc42
Site Admin
Posts: 126
Joined: Wed Oct 22, 2014 3:18 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby nc42 » Tue Mar 01, 2016 1:41 pm

Received my mini dp to dp cable today and had about 45 minutes to play around.

Ran some 3w 470nm blue leds through the ipad screen with what I think were the 3 filters closest to the screen to even the blue light out. When the screen was 35-40mm from the leds it seemed pretty even. Only had 6 leds wired up.

Had an epiphany today with testing resin. On the earlier tests the thick blobs would cure first. Oxygen inhibition in effect folded the plastic over and sandwiched the resin and it all worked a lot better. Cured around .2mm thick in around 10 seconds. Nothing to scientific though

nc42
Site Admin
Posts: 126
Joined: Wed Oct 22, 2014 3:18 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby nc42 » Tue Mar 01, 2016 1:48 pm

Few pics
Attachments
20160301_145949-1.jpg
20160301_150126-1.jpg
20160301_145758-1.jpg

nc42
Site Admin
Posts: 126
Joined: Wed Oct 22, 2014 3:18 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby nc42 » Tue Mar 01, 2016 3:26 pm

didn't have a chance to test the standard ipad screen maybe tomorrow.

AndersonTa
Posts: 189
Joined: Mon Dec 09, 2013 4:28 pm
Location: Houston, TX
Contact:

Re: Daylight Polymer 3D Printer

Postby AndersonTa » Wed Mar 02, 2016 2:11 pm

@AndersonHTa

nc42
Site Admin
Posts: 126
Joined: Wed Oct 22, 2014 3:18 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby nc42 » Wed Mar 02, 2016 3:50 pm

Tried it this afternoon. Unfortunately the second screen backlight has an issue on one side of the screen. I was still able to try even after breaking the locking bar on the FCP connector on the abusemark board.... Seemed to cure just fine in the 10-20s. Still a bit hard to say how this will translate to actual usage cure times, but encouraging. Unfortunately the screens aren't as cheap in europe as they are in the US for some reason (2+ x as much!) so I'll be waiting for a new one from china. Probably give up on the blue leds for the time being.

nc42
Site Admin
Posts: 126
Joined: Wed Oct 22, 2014 3:18 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby nc42 » Wed Mar 02, 2016 5:31 pm

Right now I'm thinking the biggest question in all this is what is a reasonably priced method of getting displayport output. For mucking about my Surface works great but I want something dedicated for the actual printer.

dpizzle
Posts: 43
Joined: Wed Aug 13, 2014 6:44 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby dpizzle » Wed Mar 02, 2016 7:57 pm

Yeah the converters can be expensive. You either have to go with HDMI->DP or USB3->DP converter. Not all of them will work, so you have to be careful. Seems the cheapest for either of these is in the $40 range. If you have a desktop just buy a $20 used graphics card on eBay that has display port.

oliveenchine
Posts: 30
Joined: Tue Feb 04, 2014 9:57 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Daylight Polymer 3D Printer

Postby oliveenchine » Wed Mar 02, 2016 10:53 pm



[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable