Bulging effect on top down DlP printer.(solved)

You can discuss Photo-sensitive resins, polymers, and oligomers.
kakapoopie
Posts: 115
Joined: Sun Jun 15, 2014 8:49 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Bulging effect on top down DlP printer.

Postby kakapoopie » Tue Nov 18, 2014 2:58 pm

Thanks Pomeroy

GUYS! Last night I did a test print with super long settle times (30s) between layers. This helped tremendously...virtually no bulging. Also increased Z height from 30um to 50um which helped the resin settle between layers. I'm thinking about getting some Spot A to test next to try to get these settle times lower. So excited about this :)

User avatar
PomeroyB
Posts: 168
Joined: Thu Mar 27, 2014 9:51 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Bulging effect on top down DlP printer.

Postby PomeroyB » Wed Nov 19, 2014 12:35 am

How fast is your build time with a 30 second dwell?

kakapoopie
Posts: 115
Joined: Sun Jun 15, 2014 8:49 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Bulging effect on top down DlP printer.

Postby kakapoopie » Wed Nov 19, 2014 3:53 am

About 8 hours for 45mm height

User avatar
PomeroyB
Posts: 168
Joined: Thu Mar 27, 2014 9:51 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Bulging effect on top down DlP printer.

Postby PomeroyB » Wed Nov 19, 2014 4:06 am

Not terrible... Especially since you're building a 50 microns!

I wonder where you begin to get diminishing returns... Is 15 seconds enough? 10? But how do you measure bulging? Just by looks? or is there some quantitative method?

I might have to do some testing on this... not too keen on the wiper solution.

kakapoopie
Posts: 115
Joined: Sun Jun 15, 2014 8:49 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Bulging effect on top down DlP printer.

Postby kakapoopie » Wed Nov 19, 2014 2:22 pm

Just by eye..mainly things that are straight in the model are now straight (which were bulging before)

Since I'm doing prints overnight, I just set maximum dwell that could fit in 8 hours. I tried 15 s actually and was still getting some bulge, but not as much. It all depends on how viscous your resin is, how thick your Z resolution is and how wide your part is.

I will definitely be trying Spot A LV next since FTD seems pretty thick. Does anyone know of any other good low viscosity resins?

firecardenal
Posts: 60
Joined: Mon Jun 16, 2014 10:03 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: Bulging effect on top down DlP printer.(solved)

Postby firecardenal » Tue Jul 07, 2015 5:01 pm



[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable