Search found 54 matches
- Mon Dec 08, 2014 9:59 am
- Forum: Software Forum
- Topic: I need some help!
- Replies: 10
- Views: 19112
Re: I need some help!
as pomeroyb please link to your firmware , so we can check , also what control board or schematic design are you following general point if stepper motors are not working is to see if when powered up the motor shaft is solid to turn if they freely move you have a problem . if the stepper drivers hav...
- Mon Dec 08, 2014 8:44 am
- Forum: LittleRP
- Topic: Connect Projector ?
- Replies: 1
- Views: 5424
Re: Connect Projector ?
modifying projector depends on what dlp printer you have but mostly consists or removing a colour wheel ( if it's fitted ) and introducing uv light , it is possible with some you dont need to do anything a good model is the acer 6104 the DLP projector is connected 2 ways 1 the rs232 control port is ...
- Mon Dec 08, 2014 8:25 am
- Forum: Software Forum
- Topic: I need some help!
- Replies: 10
- Views: 19112
Re: I need some help!
you do not say what you are connecting , but you are trying to connect both a dlp projector and your controller board to com4 i.e both the same usb ports .. this will lock up the usb machine connection = your arduino controller projector control = your dlp projector if you have any further problems ...
- Thu Dec 04, 2014 7:13 am
- Forum: Hardware
- Topic: Not enough holding power for z axis?
- Replies: 19
- Views: 34563
Re: Not enough holding power for z axis?
great glad you found it in the end ! regarding salt water , i'm skeptical it would work , are you using Tap water or distilled water, distilled will be far better , and last longer , as is at least free of any Contamination if the resin is sinking , i would hazard a guess that it's either going off ...
- Thu Dec 04, 2014 6:18 am
- Forum: Software Forum
- Topic: need b9 software modification
- Replies: 7
- Views: 13746
Re: need b9 software modification
quickreplier: yes altering the code can be done, and also using CW is an option , with some code written for it (plugin) however their are many commands used that are projector specific communications , so knowing what projector you wish to change to would be required , and you would also need to ma...
- Wed Dec 03, 2014 1:04 pm
- Forum: Hardware
- Topic: low ANSI-lumens
- Replies: 4
- Views: 9977
Re: low ANSI-lumens
i'll pm you
- Wed Dec 03, 2014 10:41 am
- Forum: Hardware
- Topic: Not enough holding power for z axis?
- Replies: 19
- Views: 34563
Re: Not enough holding power for z axis?
i'm wondering if you have the stepper enable configured incorrectly and it's working in reverse
the pots are only single turn , so once you reach max , it will drop to zero and start again , theirs no stops on the pots as you found out
what software / interface are you using ?
the pots are only single turn , so once you reach max , it will drop to zero and start again , theirs no stops on the pots as you found out
what software / interface are you using ?
- Wed Dec 03, 2014 10:17 am
- Forum: Software Forum
- Topic: Please Help!! SLA product surface problem. (photo included)
- Replies: 3
- Views: 7640
Re: Please Help!! SLA product surface problem. (photo includ
what software are you using to drive the galvo's etc ?
and i'll try and replicate your setup here
as Pacmanfan suggests it appears to be that your slicing at to wide in x y what ever your set at , try a test at 50% less
and i'll try and replicate your setup here
as Pacmanfan suggests it appears to be that your slicing at to wide in x y what ever your set at , try a test at 50% less
- Wed Dec 03, 2014 10:10 am
- Forum: Hardware
- Topic: low ANSI-lumens
- Replies: 4
- Views: 9977
Re: low ANSI-lumens
you do not give details of your DLP Projector or details of the polymer has this worked in the past and has developed this problem , or are you trying to match a projector etc , one thing to look for are additional filters and is the optic path clean etc , lamps do develop low light levels over time...
- Wed Dec 03, 2014 9:57 am
- Forum: Software Forum
- Topic: need b9 software modification
- Replies: 7
- Views: 13746
Re: need b9 software modification
i am at a loss what you need , all parts and drawings including the arduino code are available for download , along with the pcb artwork
anyhow let me know what you need .
anyhow let me know what you need .