Search found 59 matches
- Tue Apr 26, 2016 9:33 am
- Forum: LittleRP
- Topic: B9_yellow castable resin.
- Replies: 6
- Views: 15779
B9_yellow castable resin.
Hi all, Anybody had good results with this? I would like to know what your exposure settings are too. I'm using an unmodified Acer P1500 with flexvat. Many thanks! Just to add, I've been trying to print with this with epic failures! :( The resin just doesn't stick to my plate!!!!! Got the first 10 l...
- Sun Apr 24, 2016 3:01 pm
- Forum: LittleRP
- Topic: Shrinkage?
- Replies: 8
- Views: 19632
Re: Shrinkage?
So your calibration prints are all coming out fine but the ring is still coming out way too small? You didn't mention how the calibration on Z was; be sure to test that as well. I'd say that's hinting at an issue with the file itself. Maybe the STL is being auto scaled by half somewhere in the soft...
- Thu Apr 21, 2016 5:26 pm
- Forum: LittleRP
- Topic: Shrinkage?
- Replies: 8
- Views: 19632
Re: Shrinkage
Okay, so it turns out my calibrations are actually okay on X and Y. My 20x20x5 block is to close tolerations however I'm still getting a ring two sizes smaller than the original. I noticed though that whilst printing the ring, the supports on the base are almost non-existent. The ring shank seems to...
- Wed Apr 20, 2016 1:20 pm
- Forum: LittleRP
- Topic: Shrinkage?
- Replies: 8
- Views: 19632
Re: Shrinkage?
Great, I will measure a 20x20x5 block and try this out. Many thanks!!
- Tue Apr 05, 2016 3:43 pm
- Forum: LittleRP
- Topic: Shrinkage?
- Replies: 8
- Views: 19632
Re: Shrinkage?
It happens. Just in varying degrees. Normally it's only around <3%, but it's highly dependent on design, temp, and material. If your prints are 150% off then I'd say it sounds more like a calibration issue and not a shrinkage one. Ok thanks. So I guess a ring that's two sizes down is a huge percent...
- Thu Mar 31, 2016 5:48 pm
- Forum: LittleRP
- Topic: Shrinkage?
- Replies: 8
- Views: 19632
Shrinkage?
So there's lot's of talk on the internet about shrinkage. Some say it happens and some say it doesn't.
After calibration, my ring came out about a size and a half too small. Is this shrinkage or another reason to re-calibrate?
Any jewellery designers come across this issue?
After calibration, my ring came out about a size and a half too small. Is this shrinkage or another reason to re-calibrate?
Any jewellery designers come across this issue?
- Mon Mar 28, 2016 12:10 pm
- Forum: LittleRP
- Topic: Calibration help please!
- Replies: 3
- Views: 13180
Re: Calibration help please!
this may help: http://projectsinterestsandetcetera.com/setting-up-a-dlp-projector-based-3d-printers-build-size-and-resolution-for-creation-workshop/ Many thanks HTL! Yes it did help to a great degree. However I was making a huge error of not making any measurements with the VAT in place! I was plac...
- Fri Mar 18, 2016 2:25 pm
- Forum: LittleRP
- Topic: Calibration help please!
- Replies: 3
- Views: 13180
Calibration help please!
Attempted to print a couple of things.
A ring came out quite oval shaped.
The calibration grid has overhanged of the build plate.
Some detailed steps on how to calibrate would be amazing!
The overhung grid measures 62x37 so hoe this helps.
A ring came out quite oval shaped.
The calibration grid has overhanged of the build plate.
Some detailed steps on how to calibrate would be amazing!
The overhung grid measures 62x37 so hoe this helps.
- Fri Mar 18, 2016 1:28 pm
- Forum: General
- Topic: Little RP and FLex Vat
- Replies: 1
- Views: 15561
Re: Little RP and FLex Vat
Hi there! These look excellent! I've just started to use my LittleRP for jewellery making too. So far my prints and calibration are way off! My ring appeared squashed!! Perhaps you might have some tips for me to get things going properly? How exactly do you adjust resolution in CW? Sorry, completely...