Search found 28 matches
- Thu Nov 20, 2014 6:15 am
- Forum: Resins
- Topic: Why NOT use saltwater?
- Replies: 10
- Views: 29834
Re: Why NOT use saltwater?
Hello everybody, i've tested a lot and in my opinion saltwater is not the best choice. There are a lot of problems if you use it everyday. And also the cleaning of the vat with a pump makes problems with saltwater. That's the reason why i've developed my own resin replacement. With that you can use ...
- Sat Mar 08, 2014 6:00 am
- Forum: Creation Workshop
- Topic: z-axis Calibration
- Replies: 12
- Views: 24015
Re: z-axis Calibration
Thanks for you help. I fixed the problem ;-) I'm using a projector which must be connected via usb and the resolution of the projector and the second screen was not the same. It was a little bit tricky, because you have to use the software of the projector to create a second screen and not the Windo...
- Fri Mar 07, 2014 4:01 am
- Forum: Creation Workshop
- Topic: z-axis Calibration
- Replies: 12
- Views: 24015
Re: z-axis Calibration
I've got a top down printer.
So it seems to be correct, doesn't it?
So it seems to be correct, doesn't it?
- Thu Mar 06, 2014 4:56 pm
- Forum: Creation Workshop
- Topic: z-axis Calibration
- Replies: 12
- Views: 24015
Re: z-axis Calibration
Post a section of some of your generated GCode from slicing a file. Maybe I can help spot the issue ;(****Build and Slicing Parameters****) ;(Pix per mm X = 13.09147 px/mm ) ;(Pix per mm Y = 13.09091 px/mm ) ;(X Resolution = 1281 px ) ;(Y Resolution = 720 px ) ;(X Pixel Offset = 0 px ) ;(Y Pixel Of...
- Thu Mar 06, 2014 2:47 pm
- Forum: Creation Workshop
- Topic: z-axis Calibration
- Replies: 12
- Views: 24015
Re: z-axis Calibration
Hey,
i'm using a ramps 1.4 Board and all jumpers are installed. I've checked the stepper data sheet....
If i use the manual control and move the z axis 1 mm up, it goes 1mm up, but not when i'm printing.
It makes me crazy....
i'm using a ramps 1.4 Board and all jumpers are installed. I've checked the stepper data sheet....
If i use the manual control and move the z axis 1 mm up, it goes 1mm up, but not when i'm printing.
It makes me crazy....
- Thu Mar 06, 2014 8:10 am
- Forum: Creation Workshop
- Topic: z-axis Calibration
- Replies: 12
- Views: 24015
Re: z-axis Calibration
I've checked my firmware and CW.
I don't know why, but it looks like as if the z-axis is doubled in it's size.
Please help me before i'll lose all of my hair
I don't know why, but it looks like as if the z-axis is doubled in it's size.
Please help me before i'll lose all of my hair
- Thu Mar 06, 2014 7:59 am
- Forum: Resins
- Topic: top down with resin floating on water or ???
- Replies: 29
- Views: 68801
Re: top down with resin floating on water or ???
Hey, i've tested a little bit and now i've got a solution for resin floating. The resin and the solution stays stable for 3 weeks now and there are any reactions. I've got no problems until now and i was able to save nearly 150$ for resin. If there is somebody interested in getting this stuff, write...
- Wed Mar 05, 2014 9:47 am
- Forum: Creation Workshop
- Topic: z-axis Calibration
- Replies: 12
- Views: 24015
z-axis Calibration
Hey guys, after i've calibrated my dlp printer, i made a testprint. Everything is fine, but the z-axis is wrong. I mean, i printed a yoda model and it became a conehead yoda. It looks funny, but ... I use a 1.8° stepper with an 8 mm spindle. I calculated the steps per mm like this: 200(steps) x 16(1...
- Wed Jan 15, 2014 6:11 pm
- Forum: Creation Workshop
- Topic: Tilt doesn't work
- Replies: 6
- Views: 11079
Re: Tilt doesn't work
Now i've tried Sprinter in RepetierHost and the same problem. With Marlin the same. I don't know what to do. It sounds like the stepper wants to move but it doesn't. I've checked the way of the stepper and there is nothing what stops the stepper. I've test different kinds of configurations in the Ar...
- Wed Jan 15, 2014 12:27 pm
- Forum: Creation Workshop
- Topic: Tilt doesn't work
- Replies: 6
- Views: 11079
Re: Tilt doesn't work
Have you tired to send a few GCode commands? Yes, i tried to send a Code like you've written and it was the same. You can hear a quiet noise but nothing moves. For Repetier i use Marlin and it works very well. For CW i use Sprinter and the Z-Axis works fine and if i switch the wires of the stepper,...