It works now! I disabled temperature sensors.
#define TEMP_SENSOR_0 0 // 0 instead of 1!!
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_BED 1
Search found 22 matches
- Fri Aug 14, 2015 9:27 am
- Forum: Creation Workshop
- Topic: Ramps Testcode works, CW does not, what to do?
- Replies: 6
- Views: 17689
- Fri Aug 14, 2015 7:29 am
- Forum: Creation Workshop
- Topic: Ramps Testcode works, CW does not, what to do?
- Replies: 6
- Views: 17689
Re: Ramps Testcode works, CW does not, what to do?
Is it possible to run Marlin firmware without endstops? At the moment I have working setup with Sprinter but I would like to add servo shutter so I guess I need Marlin. But I just can't make it work....
- Fri Aug 14, 2015 4:10 am
- Forum: Buy / Sell / Trade
- Topic: Buy Teflon, FEP Film
- Replies: 23
- Views: 58740
Re: Buy Teflon, FEP Film
Hi people, At the moment I could get some 0.05mm FEP foil leftovers. But still I have to take all of them so that is like 20m2... Is anyone here interested? Price would be around 50€/m2 + shipping. It is from 1,2m roll. I am from Europe but I have no problem sending to other countries. If there is e...
- Mon Aug 03, 2015 4:13 pm
- Forum: Hardware
- Topic: Z-axis Configuration and Stepper Problems
- Replies: 2
- Views: 11478
Re: Z-axis Configuration and Stepper Problems
If you are using modified ATX you need continuous load. In order to fix that people wire 10 Ohm 10W power resistor (or something close of that) that acts as continuous load. This might be your problem... Otherwise I am having the same problems with speed and time calculation. If anyone have an idea ...
- Fri Jun 12, 2015 3:12 am
- Forum: Creation Workshop
- Topic: Connecting to CW Host problem
- Replies: 0
- Views: 8986
Connecting to CW Host problem
Hi. I have problem with connecting my Chinese Ramps 1.4 and Raspberry pi. I have installed CW Host as written on Github, Ramps 1.4 works (I checked with test code if stepper spins). But when I try to connect from PC browser it shows me CW Host interface but I can't do anything. "Problem communi...
- Tue May 19, 2015 1:44 pm
- Forum: Software Forum
- Topic: Working Marlin Firmware
- Replies: 13
- Views: 38981
Re: Working Marlin Firmware
Thank a lot
- Fri May 15, 2015 11:53 am
- Forum: Software Forum
- Topic: Working Marlin Firmware
- Replies: 13
- Views: 38981
Re: Working Marlin Firmware
Or if anyone else could upload configured Merlin/Sprinter firmware which works with CW? Thank you in advance.
- Fri May 15, 2015 11:11 am
- Forum: Software Forum
- Topic: Working Marlin Firmware
- Replies: 13
- Views: 38981
Re: Working Marlin Firmware
Uploaded this to DB for anyone that is wanting to use Marlin on there DLP build with CW. It is setup to use a hobby servo off of pin D11 You will need to change the max travel limits after homing to fit your build, this uses one end stop for the Z and software limited for the height. End stops will...
- Thu Mar 12, 2015 6:48 am
- Forum: Creation Workshop
- Topic: Custom resolution option
- Replies: 29
- Views: 58280
Custom resolution option
Hi. In CW is it possible to setup custom resolution in order to export PNG slices for projector that is not connected to the CW? Because at the moment I am testing my DLP and I would like to simply project pictures using Powerpoint...
- Wed Mar 11, 2015 4:14 am
- Forum: Creation Workshop
- Topic: User Manual and Hardware Guide
- Replies: 2
- Views: 10759
Re: User Manual and Hardware Guide
Thank you very much