Search found 54 matches
- Sun Nov 23, 2014 7:44 am
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 132654
Re: How to move CW stepper motors?
ok so the program is working have you adjusted the steps to match your machine configuration in the arduino code ? as instructed (PlatenStepsPerLayer) and set the switches on your stepper driver to match ( 16 microsteps) see this section in the arduino code: > adjust "PlatenStepsPerLayer" ...
- Fri Nov 21, 2014 9:18 am
- Forum: Software Forum
- Topic: Manual Jog Wheel for Z-Axis movement
- Replies: 6
- Views: 12005
Re: Manual Jog Wheel for Z-Axis movement
going by memory the encoder pins are :
The middle pin attaches to ground. the other two to pins D33 and D35 on your ramps AUX-4 connector
the centre shaft push switch is D29 and ground
The middle pin attaches to ground. the other two to pins D33 and D35 on your ramps AUX-4 connector
the centre shaft push switch is D29 and ground
- Fri Nov 21, 2014 5:59 am
- Forum: Hardware
- Topic: Z-Axis from Kickstarter
- Replies: 8
- Views: 14674
Re: Z-Axis from Kickstarter
i'll guess that your exposure time , is too high
try lowering the exposure until it's just not curing then add 10- 15%
worth a try either way
try lowering the exposure until it's just not curing then add 10- 15%
worth a try either way
- Fri Nov 21, 2014 5:54 am
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 132654
Re: How to move CW stepper motors?
if you are 100% that you do not recieve "ok" when using the arduino terminal the problem is your arduino code is not uploaded or running correctly. this needs to be correct before you can move on to CW . check you are uploading the arduinocode correctly to the correct comport & board s...
- Thu Nov 20, 2014 1:42 pm
- Forum: Hardware
- Topic: Z-Axis from Kickstarter
- Replies: 8
- Views: 14674
Re: Z-Axis from Kickstarter
looks ok , i cant see any valid reason to change , is that a 10x2 screw your using or x5 , cant quite see from the picture
have you a problem with your z ?
have you a problem with your z ?
- Thu Nov 20, 2014 12:34 pm
- Forum: Hardware showcase / Build Logs
- Topic: New LaserShark Based SLA Build
- Replies: 15
- Views: 38705
Re: New LaserShark Based SLA Build
here is some more information on adjusting the 20k drivers , ive copy'd just about most of it to make sense i think . it does say to use a ilda test pattern from lasershark . or will have to see about probable producing a test pattern as gcode for example .so it can be used from CW is my suggestion ...
- Thu Nov 20, 2014 11:28 am
- Forum: Hardware showcase / Build Logs
- Topic: New LaserShark Based SLA Build
- Replies: 15
- Views: 38705
Re: New LaserShark Based SLA Build
attached is more more information general to 20k scanners
although it shows using the showcard , it does give a small insight to setting the card
although it shows using the showcard , it does give a small insight to setting the card
- Thu Nov 20, 2014 11:19 am
- Forum: Hardware showcase / Build Logs
- Topic: New LaserShark Based SLA Build
- Replies: 15
- Views: 38705
Re: New LaserShark Based SLA Build
thanks Andy , your pic just about bears out my sketchy list .. thanks .. anyhow back to your problem. swap over just the driver boards and lets see what the answers give , it will denote the next step .. as another test you could also just swap over the inputs from the lasershark , just in case your...
- Thu Nov 20, 2014 10:03 am
- Forum: Hardware
- Topic: Z-Axis from Kickstarter
- Replies: 8
- Views: 14674
Re: Z-Axis from Kickstarter
yes i'd agree , but precision is additive , depending on what is driving it , steppers , servo's , let alone to the depths of the associated drivers also to be able to make an item to a given dimension you need equipment , 10 times more accurate so overall i'd doubt their claims (nicely) as your now...
- Thu Nov 20, 2014 9:53 am
- Forum: Hardware showcase / Build Logs
- Topic: New LaserShark Based SLA Build
- Replies: 15
- Views: 38705
Re: New LaserShark Based SLA Build
i'm presuming your drivers are 20k the only information i have on the 20k scanner set is a little sketchy , ( nothing new there with chinese manuals ) see the attached information as to what the pots do they are quite touchy , and you'll find some adjustments will affect others , so beware if anythi...