Search found 116 matches

by dangre
Mon Jun 08, 2015 10:03 am
Forum: General
Topic: Post Cure Lamp
Replies: 7
Views: 13798

Re: Post Cure Lamp

I'm curious how this compares to the 4 x 9w=36w fingernail cure lamps? I've learned much about how wattage may not be the best measurement of actual UV output. Love to see a spectral output map of this lamp. Just curious.
by dangre
Mon Jun 01, 2015 1:15 pm
Forum: Software Forum
Topic: Please move 'Home' button!!
Replies: 4
Views: 5357

Re: Please move 'Home' button!!

For those of us using smaller tablet PC's, I was wondering if you could make the most used buttons larger. The Home, Z+, etc buttons are tough to pick with a fat finger on a tiny 8" screen. The menu bar buttons for Play, Pause, Stop are very selectable. There are only a couple buttons that we u...
by dangre
Fri May 22, 2015 11:12 am
Forum: Commerical Machines
Topic: Solus High Resolution DLP 3D Printer
Replies: 41
Views: 43515

Re: Solus High Resolution DLP 3D Printer

Cerrious,
I had the same issue with Chrome. I googled refiy-3d and it gave me the same exact address but it worked.
Great looking printer by the way...
by dangre
Wed May 20, 2015 9:32 am
Forum: Creation Workshop
Topic: Machine Com Port, can't set <solved>
Replies: 4
Views: 4847

Re: Machine Com Port, can't set

by dangre
Tue May 19, 2015 10:18 am
Forum: Creation Workshop
Topic: Machine Com Port, can't set <solved>
Replies: 4
Views: 4847

Re: Machine Com Port, can't set

Update: I was able to resolve the communication issue by moving CW to the SD card. I can only assume I may have a Windows8 administration access issue. I am not a Win8 expert but this fix works for me. I'll ask around for advice on Win8. For the time being, I am happy with my $99 CW/3D printer compu...
by dangre
Mon May 18, 2015 2:41 pm
Forum: Creation Workshop
Topic: Machine Com Port, can't set <solved>
Replies: 4
Views: 4847

Machine Com Port, can't set <solved>

I was hoping someone can shed some light on my communication issue. I have been successfully running my printer with CW for a year on a couple different laptops. I just purchased a WinBook Win8 tablet and cannot get the Arduino(RAMPS) to communicate with CW and the tablet. I can see the Com port (CO...
by dangre
Mon May 18, 2015 10:10 am
Forum: Creation Workshop
Topic: Lines.. Everywhere, lots of them
Replies: 3
Views: 4305

Re: Lines.. Everywhere, lots of them

I have the best luck with NetFabb software...
by dangre
Fri May 15, 2015 11:23 am
Forum: Vat Design and Construction
Topic: Torque wrench for tightening flexvat bolts
Replies: 10
Views: 11131

Re: Torque wrench for tightening flexvat bolts

hegykc, I have had failure due to improperly tensioned FEP. I was pulling my hair out when I could not get adhesion to my build plate after a FEP change. After draining my vat thinking it was the resin, I noticed the FEP did not sound the same as normal. When I 'thumped' the FEP it had a higher pitc...
by dangre
Thu May 14, 2015 11:52 am
Forum: Vat Design and Construction
Topic: Torque wrench for tightening flexvat bolts
Replies: 10
Views: 11131

Re: Torque wrench for tightening flexvat bolts

My vat does not use a gasket (acrylic/FEP/UHMW) but the resin does 'wick' in between layers by capillary action. No 'leaking'. I will add a gasket to my next design. I think the resistance of my tight UHMW tapped holes would make torque measurements inaccurate in relation to FEP tension. But nothing...
by dangre
Fri May 08, 2015 4:15 pm
Forum: LittleRP
Topic: FEP vat for the LittleRP?
Replies: 66
Views: 49316

Re: FEP vat for the LittleRP?

I've always wanted to know how much (if any) UV is filtered by Acrylic and this would be a good test if you did not cut out the center of the base and compare exposure times. It would help lessen sagging (more affected on big vats).