Search found 50 matches
- Mon Sep 21, 2015 6:48 pm
- Forum: Electronics
- Topic: How to implement limit on the Arduino Mega 2560 and Cw
- Replies: 7
- Views: 19796
Re: How to implement limit on the Arduino Mega 2560 and Cw
I'm sorry about my English. Some times I can not write in English as i think in Portuguese. When i use pin 18 (minimum Z) my plataform goes down, find the dispositive wich closes the pin 18 and GND, and then goes up a few milimeters. I want it to stay exactly where is the travel end without goes bac...
- Sat Sep 19, 2015 7:15 pm
- Forum: Electronics
- Topic: How to implement limit on the Arduino Mega 2560 and Cw
- Replies: 7
- Views: 19796
Re: How to implement limit on the Arduino Mega 2560 and Cw
sodio Thank you for your prompt reply I uploaded with Arduino and now 1.0.5 installed . My question is : which pin to use for the end of course , want to take the construction platform for home? If use the pin 18 and returns to the platform a few millimeters , this can not happen because then the co...
- Fri Sep 18, 2015 2:06 pm
- Forum: Electronics
- Topic: How to implement limit on the Arduino Mega 2560 and Cw
- Replies: 7
- Views: 19796
Re: How to implement limit on the Arduino Mega 2560 and Cw
Hi, tahnks for your help. I had a problem working with your code. Look at: Arduino: 1.6.4 (Windows 7), Placa:"Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)" SdFatUtil.cpp.o: In function `SdFatUtil::FreeRam()': C:\Users\Windows\AppData\Local\Temp\build8906941252038550266.tmp/SdFatUtil.c...
- Sat Aug 29, 2015 5:13 pm
- Forum: Electronics
- Topic: How to implement limit on the Arduino Mega 2560 and Cw
- Replies: 7
- Views: 19796
How to implement limit on the Arduino Mega 2560 and Cw
Hello everyone
Does anyone happen to know how do I for a limit on the Z axis of a DLP printer that works with the CW , and Marlim , ramps . ?
I thank you for the attention
Does anyone happen to know how do I for a limit on the Z axis of a DLP printer that works with the CW , and Marlim , ramps . ?
I thank you for the attention
- Mon Mar 02, 2015 11:44 am
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 133944
Re: How to move CW stepper motors?
Pomeroy Now I got. It was understood that the logic is: X, Y and Z, respectively. But something happened, X and Z axes work in unison, when should the Tilt (X) act first to take off the slice and then the Z up. Another thing: I could not change the acceleration of the axes, change the values in that...
- Sat Feb 28, 2015 5:26 pm
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 133944
Re: How to move CW stepper motors?
Pomeroy
I changed the line values 513, I uploaded but does not change anything on the scale. remains always the same thing. no matter what value I place
To give you a light: my time is 2mm and my driver are selected for 1/16 .Motores 200 steps per revolution.
I changed the line values 513, I uploaded but does not change anything on the scale. remains always the same thing. no matter what value I place
To give you a light: my time is 2mm and my driver are selected for 1/16 .Motores 200 steps per revolution.
- Sat Feb 28, 2015 9:47 am
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 133944
Re: How to move CW stepper motors?
Pomeroy
Finally progress ........
I managed to move the axes , however had to use the Ultimaker that came with Marlin .
Now I have to set the scale, which I did not find where it is. If within Marlim or Ultimaker ?
if you can give more this tip , it would be very good .
Dall Aura
Finally progress ........
I managed to move the axes , however had to use the Ultimaker that came with Marlin .
Now I have to set the scale, which I did not find where it is. If within Marlim or Ultimaker ?
if you can give more this tip , it would be very good .
Dall Aura
- Fri Feb 27, 2015 6:15 pm
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 133944
Re: How to move CW stepper motors?
Pomeroy changed the pinspRAMPS-13 files - I uploaded to the Arduino, but this is with the LED always on. See photo below, this LED does not turn off ever, and Will not managed to move the engines. I put as I had here: X pin 3 step X pin 2 direction Z pin 6 step Z direction pin 2 Just do not put enab...
- Wed Feb 25, 2015 7:37 pm
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 133944
Re: How to move CW stepper motors?
Pomeroy
Congratulations
It is people like you who change the world.
Now I have a lot of information, I will follow them to slowly, I inform you.
ABRC
Congratulations
It is people like you who change the world.
Now I have a lot of information, I will follow them to slowly, I inform you.
ABRC
- Wed Feb 25, 2015 11:55 am
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 133944
Re: How to move CW stepper motors?
The latest version of Marlin can always be found at its Github . To get the files, click the "Download Zip" button on the left. I did not find where to set the pins of the stepper motors. The first thing you need to do is to determine what your board is set up as. I suggest just pretendin...