Search found 54 matches
- Sun Jan 11, 2015 10:01 am
- Forum: Software Forum
- Topic: stepper motor is not working properly
- Replies: 6
- Views: 18747
Re: stepper motor is not working properly
the default x16 microstepping is with all 3 links on (ms1.2.3 ) ,
- Tue Jan 06, 2015 1:07 pm
- Forum: Hardware showcase / Build Logs
- Topic: Powder Module for SLS/Inkjet-Binder
- Replies: 4
- Views: 15438
Re: Powder Module for SLS/Inkjet-Binder
certainly interested in helping out and assisting here
the major prob i'm in the UK
regards
the major prob i'm in the UK
regards
- Sun Jan 04, 2015 5:26 pm
- Forum: Software Forum
- Topic: stepper motor is not working properly
- Replies: 6
- Views: 18747
Re: stepper motor is not working properly
what microsteps have you set on the big easy stepper ( ms1,ms2,ms3)
what power supply are you using and also what ballscrew or threaded rod are you using for z , this needs to be set correctly
what power supply are you using and also what ballscrew or threaded rod are you using for z , this needs to be set correctly
- Thu Jan 01, 2015 9:15 am
- Forum: General
- Topic: DVD reader is a SLA printer
- Replies: 14
- Views: 29126
Re: DVD reader is a SLA printer
dvd's steppers are pretty standard try 20 steps dvd motor spec ( resonably standard ) pl15s020.pdf https://github.com/taksan/Arduino-Lab/blob/master/stepperHack/PL15S020.pdf the problem you will have is that the tb6560 , suit 1.8 deg steppers , where dvd steppers are 18 deg per step so they probably...
- Tue Dec 23, 2014 2:58 pm
- Forum: General
- Topic: Water beading issue on resin surface
- Replies: 1
- Views: 5856
Re: Water beading issue on resin surface
it's probable your salt to water ratio is not enough , or that your water is contaminated , especially if you have used a different resin in the same tank before make sure the tank is clean using Isopropyl alcohol and make sure the tank is dry , try fresh de-ionised water and fresh salts . if the sa...
- Mon Dec 22, 2014 6:51 am
- Forum: Software Forum
- Topic: How to move CW stepper motors?
- Replies: 68
- Views: 138209
Re: How to move CW stepper motors?
what are you trying ?? i thought you were using a Uno with only a z axis , and now your trying to use Marlin this will not work on a uno , PLEASE describe your setup,and show us what electronics you have you seem to be trying every mix in the pot , trying to find something that will work , this is n...
- Sun Dec 21, 2014 3:43 pm
- Forum: Software Forum
- Topic: Working Marlin Firmware
- Replies: 13
- Views: 40947
Re: Working Marlin Firmware
all settings are in configuration.h
this also depends on what breakout board your using such as ramps or sanguino etc
this also depends on what breakout board your using such as ramps or sanguino etc
- Fri Dec 12, 2014 4:59 am
- Forum: Hardware
- Topic: Motors not working well.. A Progressive Issue
- Replies: 8
- Views: 17179
Re: Motors not working well.. A Progressive Issue
what are you using for a power supply ?
- Fri Dec 12, 2014 4:56 am
- Forum: General
- Topic: Pico Projector base 3D printer
- Replies: 5
- Views: 15941
Re: Pico Projector base 3D printer
nehal: The problem you face is that their is little in the way of exact information out there , however you have come to the right spot the links to Pacmanfans blog and posts is about the best available at this time , with specific interest to Pico i would read all you can and come back with specifi...
- Thu Dec 11, 2014 5:26 am
- Forum: Hardware
- Topic: Motors not working well.. A Progressive Issue
- Replies: 8
- Views: 17179
Re: Motors not working well.. A Progressive Issue
motors seizing up or intermittent moves , etc , is down to trying to move the motors faster than they are capable given the accelleration and velocity settings your trying to use either in the firmware defaults or too high a feed rate etc slow everything down ,and also recheck the microstepping is c...