Search found 13 matches
- Mon Apr 13, 2015 5:12 am
- Forum: Software Forum
- Topic: ..It just wont go down.
- Replies: 8
- Views: 20037
Re: ..It just wont go down.
I see, I see. If you can get it to move in both directions then you're wired up fine. Hmmmm.... as for what causing the problem for you I don't know. Keep updating, someone is bond to figure it out. do you know if its possible to send Gcode commands through CW? Yes, it is possible. In your machine ...
- Sun Apr 12, 2015 3:10 pm
- Forum: Software Forum
- Topic: ..It just wont go down.
- Replies: 8
- Views: 20037
- Sun Apr 12, 2015 2:09 pm
- Forum: Software Forum
- Topic: ..It just wont go down.
- Replies: 8
- Views: 20037
Re: ..It just wont go down.
I have zero knowledge as far as software goes regarding Creation Workshop, however, I just wanted to say that there is a situation related to all stepper motor applications where you can have the stepper motor wired wrong and as a result it will only rotate in one direction. If you cannot get it to...
- Sun Apr 12, 2015 12:17 pm
- Forum: Software Forum
- Topic: ..It just wont go down.
- Replies: 8
- Views: 20037
- Sun Apr 12, 2015 10:23 am
- Forum: Software Forum
- Topic: ..It just wont go down.
- Replies: 8
- Views: 20037
..It just wont go down.
I've been away for a while, now I'm back, I started troubleshooting, which ended with that I starting in scratch again and took to me what was given as proposed earlier. i loaded the latest marlin firmware, i have only one opto-endstop in the setup, the Z axis will home, but wont go down, this is wh...
- Mon Jan 26, 2015 1:49 pm
- Forum: Software Forum
- Topic: help, shortguide for setup firmware?
- Replies: 11
- Views: 22432
Re: help, shortguide for setup firmware?
When the axis moves in only one direction, it's usually because the endstop is inverted. -Steve okey, i tried to set const bool Z_MAX_ENDSTOP_INVERTING = false; const bool Z_MIN_ENDSTOP_INVERTING = false; to true, however, now it wont go anywhere by clicking "home". however, when i affect...
- Sun Jan 25, 2015 11:46 am
- Forum: Software Forum
- Topic: help, shortguide for setup firmware?
- Replies: 11
- Views: 22432
Re: help, shortguide for setup firmware?
got the diod, now everything work... almost... i succeeded to revert the endstops, however, i cant run up/down manually, only home works and then it goes one direction...... suggestions..? #ifndef CONFIGURATION_H #define CONFIGURATION_H #include "boards.h" #define STRING_VERSION_CONFIG_H _...
- Wed Jan 21, 2015 1:31 pm
- Forum: Software Forum
- Topic: help, shortguide for setup firmware?
- Replies: 11
- Views: 22432
Re: help, shortguide for setup firmware?
nevermind, found this
http://forums.reprap.org/read.php?219,259333
and im gonna replace D2
http://reprap.org/mediawiki/images/f/f6 ... ematic.png
good start on this project
http://forums.reprap.org/read.php?219,259333
and im gonna replace D2
http://reprap.org/mediawiki/images/f/f6 ... ematic.png
good start on this project
- Wed Jan 21, 2015 8:16 am
- Forum: Software Forum
- Topic: help, shortguide for setup firmware?
- Replies: 11
- Views: 22432
Re: help, shortguide for setup firmware?
ok, uhm, i might have found something why the motor wont work. every time i turned on the power supply, the green lamp just went black at the power supply, so when i disconnected the power supply from the ramps, removed all electronics and still, it seems that is a short circuit between incoming + a...
- Wed Jan 21, 2015 7:11 am
- Forum: Software Forum
- Topic: help, shortguide for setup firmware?
- Replies: 11
- Views: 22432
Re: help, shortguide for setup firmware?
thanks for the replys, me english not so good, i will dubblecheck everything :) im have been following this guide just to begin, but. http://solidutopia.com/marlin-firmware-user-guide-basic/ the motor steps per revolution for me is 1.8 the microsteppings jumpers are 1/16, 16x i mean :) steps per mm ...