Search found 13 matches

by mandy
Mon Apr 13, 2015 5:12 am
Forum: Software Forum
Topic: ..It just wont go down.
Replies: 8
Views: 7062

Re: ..It just wont go down.

I see, I see. If you can get it to move in both directions then you're wired up fine. Hmmmm.... as for what causing the problem for you I don't know. Keep updating, someone is bond to figure it out. do you know if its possible to send Gcode commands through CW? Yes, it is possible. In your machine ...
by mandy
Sun Apr 12, 2015 3:10 pm
Forum: Software Forum
Topic: ..It just wont go down.
Replies: 8
Views: 7062

Re: ..It just wont go down.

by mandy
Sun Apr 12, 2015 2:09 pm
Forum: Software Forum
Topic: ..It just wont go down.
Replies: 8
Views: 7062

Re: ..It just wont go down.

I have zero knowledge as far as software goes regarding Creation Workshop, however, I just wanted to say that there is a situation related to all stepper motor applications where you can have the stepper motor wired wrong and as a result it will only rotate in one direction. If you cannot get it to...
by mandy
Sun Apr 12, 2015 12:17 pm
Forum: Software Forum
Topic: ..It just wont go down.
Replies: 8
Views: 7062

Re: ..It just wont go down.

by mandy
Sun Apr 12, 2015 10:23 am
Forum: Software Forum
Topic: ..It just wont go down.
Replies: 8
Views: 7062

..It just wont go down.

I've been away for a while, now I'm back, I started troubleshooting, which ended with that I starting in scratch again and took to me what was given as proposed earlier. i loaded the latest marlin firmware, i have only one opto-endstop in the setup, the Z axis will home, but wont go down, this is wh...
by mandy
Mon Jan 26, 2015 1:49 pm
Forum: Software Forum
Topic: help, shortguide for setup firmware?
Replies: 11
Views: 9777

Re: help, shortguide for setup firmware?

When the axis moves in only one direction, it's usually because the endstop is inverted. -Steve okey, i tried to set const bool Z_MAX_ENDSTOP_INVERTING = false; const bool Z_MIN_ENDSTOP_INVERTING = false; to true, however, now it wont go anywhere by clicking "home". however, when i affect...
by mandy
Sun Jan 25, 2015 11:46 am
Forum: Software Forum
Topic: help, shortguide for setup firmware?
Replies: 11
Views: 9777

Re: help, shortguide for setup firmware?

got the diod, now everything work... almost... i succeeded to revert the endstops, however, i cant run up/down manually, only home works and then it goes one direction...... suggestions..? #ifndef CONFIGURATION_H #define CONFIGURATION_H #include "boards.h" #define STRING_VERSION_CONFIG_H _...
by mandy
Wed Jan 21, 2015 1:31 pm
Forum: Software Forum
Topic: help, shortguide for setup firmware?
Replies: 11
Views: 9777

Re: help, shortguide for setup firmware?

nevermind, found this
http://forums.reprap.org/read.php?219,259333

and im gonna replace D2
http://reprap.org/mediawiki/images/f/f6 ... ematic.png

good start on this project ;)
by mandy
Wed Jan 21, 2015 8:16 am
Forum: Software Forum
Topic: help, shortguide for setup firmware?
Replies: 11
Views: 9777

Re: help, shortguide for setup firmware?

ok, uhm, i might have found something why the motor wont work. every time i turned on the power supply, the green lamp just went black at the power supply, so when i disconnected the power supply from the ramps, removed all electronics and still, it seems that is a short circuit between incoming + a...
by mandy
Wed Jan 21, 2015 7:11 am
Forum: Software Forum
Topic: help, shortguide for setup firmware?
Replies: 11
Views: 9777

Re: help, shortguide for setup firmware?

thanks for the replys, me english not so good, i will dubblecheck everything :) im have been following this guide just to begin, but. http://solidutopia.com/marlin-firmware-user-guide-basic/ the motor steps per revolution for me is 1.8 the microsteppings jumpers are 1/16, 16x i mean :) steps per mm ...