Search found 12 matches

by danthehuman
Fri Aug 18, 2017 1:18 am
Forum: Software Forum
Topic: MonoWare Lite - Slicing and control software for resin printers
Replies: 56
Views: 40299

Re: MonoWare Lite - Slicing and control software for resin printers

I'm using the current version found here


Also CW to control the print, with three axis
X= Wiper
Y= Projector Height
Z= Build Table

My printer is a top down setup
by danthehuman
Mon Aug 14, 2017 3:27 am
Forum: Software Forum
Topic: MonoWare Lite - Slicing and control software for resin printers
Replies: 56
Views: 40299

Re: MonoWare Lite - Slicing and control software for resin printers

How is the marlin firmware supported version coming along?
by danthehuman
Sun Aug 13, 2017 3:10 am
Forum: Creation Workshop
Topic: Create a mask with UV sensor
Replies: 40
Views: 36404

Re: Create a mask with UV sensor

Great guide, I followed it to completion and got a good result, I did find the steps in Rhino, took a bit to figure out. By following the guide up to the point of importing your excel results into Rhino, I came across is this software https://www.youtube.com/watch?v=1vMdeWVewV8 My results ranged fro...
by danthehuman
Sat Jul 15, 2017 10:27 pm
Forum: Creation Workshop
Topic: Is Creation Workshop still supported?
Replies: 1
Views: 3628

Is Creation Workshop still supported?

Is Creation Workshop still having updates and improvements done to it? as currently still one of the main printer control software that's available for the DIYer.
PacManFan are you still out there and can shed some light on where this software is at and any further plans for it?
by danthehuman
Sat Jul 15, 2017 9:35 pm
Forum: General
Topic: Switching from bottom-up to top-down -> typical problems
Replies: 4
Views: 7644

Re: Switching from bottom-up to top-down -> typical problems

I've switched to a top down print setup, and i've found the following issues and work around's Resin surface tension that effects the layer height: I run a resin heater to keep the viscosity's consistent between printing at different times during the day / night, I aim for 25 deg C and use the follo...
by danthehuman
Sat Jul 15, 2017 12:37 am
Forum: Software Forum
Topic: MonoWare Lite - Slicing and control software for resin printers
Replies: 56
Views: 40299

Re: MonoWare Lite - Slicing and control software for resin printers

Any update on the marlin firmware support and adding a wiper between each exposure on the X axis?
by danthehuman
Thu Jul 06, 2017 3:45 pm
Forum: Software Forum
Topic: MonoWare Lite - Slicing and control software for resin printers
Replies: 56
Views: 40299

Re: MonoWare Lite - Slicing and control software for resin printers

How are you getting on with the marlin version?
Also is there the option for a wiper, on say the X or Y axis that can run once the Z axis has finished moving?
by danthehuman
Sat Jun 17, 2017 11:30 pm
Forum: Software Forum
Topic: Monkeyprint open source Software for resin printers?
Replies: 11
Views: 11263

Re: Monkeyprint open source Software for resin printers?

I'm interested in giving it a go, will it be functional on windows 7 and marlin firmware?
by danthehuman
Sat Jun 17, 2017 8:56 pm
Forum: Software Forum
Topic: MonoWare Lite - Slicing and control software for resin printers
Replies: 56
Views: 40299

Re: MonoWare Lite - Slicing and control software for resin printers

Currently I have the marlin software tuned quite well for the printer and I'm adverse to changing it, when I can just wait to test it when you get around to adding support for marlin. I have a top down printer, and my biggest issue at the moment is controlling the surface of the liquid and light exp...